



Study with the several resources on Docsity
Earn points by helping other students or get them with a premium plan
Prepare for your exams
Study with the several resources on Docsity
Earn points to download
Earn points by helping other students or get them with a premium plan
Community
Ask the community for help and clear up your study doubts
Discover the best universities in your country according to Docsity users
Free resources
Download our free guides on studying techniques, anxiety management strategies, and thesis advice from Docsity tutors
PA state inspection categories test exam questions with correct answers 2024.PA state inspection categories test exam questions with correct answers 2024.PA state inspection categories test exam questions with correct answers 2024.
Typology: Exams
1 / 5
This page cannot be seen from the preview
Don't miss anything!
How should Suspension components be maintained? - Correct answer every suspension component shall be in safe operating condition how should steering components be maintained? - Correct answer the steering component should be in safe operating conditions the steering wheel shall have a minimum outside diameter of ?? - Correct answer 13 inches a passenger car manufactured after June 30, 1967 and designated as a 1968 or later model shall be equipped with what? - Correct answer service brake system with rupture failure design that doesn't not result in complete brake loss brake lines shall be approved for use as - Correct answer brake lines what shall a vehicle specified in this chapter be equipped with? - Correct answer parking brake what should a parking brake be adequate to hold the vehicle on? - Correct answer ice or snow on a 20% grade a radial ply tire shall not be used on? - Correct answer the same axle as a belted or bias tire different types of tires - Correct answer different types of tires shall not be used on the same axle unless in the event of an emergency Non-Pneumatic tires - Correct answer only if originally equipped by the manufacturer and or an antique vehicle ice grips or studs - Correct answer may not be equipped if they have projections greater than 2/32nds tires and rims - Correct answer must meet or beat manufacturer specs spacers can be no thicker than - Correct answer 1/4 inch what head lamp system should your vehicle be equipped with - Correct answer two or four head lamp system low beam candle watts must be brighter than? - Correct answer 7500
high beam candle watts cannot be less than? - Correct answer 10, total candle wattage cannot exceed? - Correct answer 150,000 watts lamps must be visible from how far? - Correct answer 500 feet brake lamps must be visible from - Correct answer 100 feet how many flashes should turn signals be per minute? - Correct answer 60- tag lights should be visible from - Correct answer 50 feet window tint must not pass which line - Correct answer AS1 line all mirrors must be what? - Correct answer crack free, hold position they are fixed to and be able to see 200 feet how many cycles per minute do wipers make - Correct answer 45 cycles per minute how far should a horn be heard from? - Correct answer 200 feet fender flares must not exceed? - Correct answer 3 inches car bumper when measured from lowest point are how high off the ground? - Correct answer 16-20 inches no higher no lower how high are truck bumpers when measured from the lowest point? - Correct answer 16-30 inches no higher no lower two adjacent tread depths of _______ or less fails a car - Correct answer 2/32nds two adjacent tread depths of _______ or less fails a truck - Correct answer 4/32nds what type of construction should your head lamps be in a two lamp construction? - Correct answer type 2 what type of construction should your head lamps be in a four lamp construction? - Correct answer two lamps shall be type 2 construction and two lamps shall be of type 1 one contruction what kind of dimming switch must be installed? - Correct answer manual dimming switch, and auto can be installed in addition to the manual switch stop lamps hazards and warning lights must be visible from? - Correct answer 100feet
rear views mirrors must have a minimum surface space of? - Correct answer 19. square inches at least a 4x5 mirror windshield defroster shall be? - Correct answer im working conditions windshield washers shall be installed in vehicles produced after? - Correct answer 1968 model year wipers shall be in - Correct answer good working order not tattered cracked or falling apart fuel systems shall be - Correct answer leak proof, intact and fastened properly accelerator control shall - Correct answer be capable of returning to idle speedometer have to? - Correct answer work odometers have to - Correct answer work unless its over 25 years old exhaust systems - Correct answer all components must be present and meet or exceed manufacturer specs and not be excessively loud, have a heat shield. fenders should not be? - Correct answer in contact with the wheels hood and hood latches should - Correct answer be present, cover the engine, be free of holes and lock on latch protruding objects - Correct answer shall not be glass, metal or plastic dislocated or dislodged from the vehicle doors must be? - Correct answer present, function as to open and close securely, unless modified to have no roof or side, tailgates can be removed if there is a net wooden plant or optional equipment present to secure contents vehicle frame shall be? - Correct answer solid motor mounts shall be - Correct answer not broken, crack free or missing flooring should be - Correct answer able to support occupants hole free. bumpers - Correct answer shall be securely attached, meet or exceed oe specs, and can be a wood plank affixed to a steel bumper seat shall be - Correct answer have no springs protruding and adjusting mechanism must work
safety belts should be - Correct answer equipped, not frayed, and have working belt buckles